Download Aruba Certified Switching Expert Written Exam.HPE6-A69.VCEplus.2024-11-16.35q.vcex
| Vendor: | HP |
| Exam Code: | HPE6-A69 |
| Exam Name: | Aruba Certified Switching Expert Written Exam |
| Date: | Nov 16, 2024 |
| File Size: | 5 MB |
How to open VCEX files?
Files with VCEX extension can be opened by ProfExam Simulator.
Discount: 20%
Demo Questions
Question 1
Refer to the exhibit.
A customer has implemented this ArubaOS-CX solution. NetEdit is not present. After a while, the secondary node of the VSX-cluster fails. What is the correct procedure to replace the failed node as quickly as possible?
- Replace the failed unit, boot up the new node without connecting cables, upgrade firmware and configure as secondary vsx node connect iSl and wart for VSX to synchronize After successful recovery, reconnect theremaining cables.
- Replace the failed unit, boot up the new node without connecting cables, upgrade firmware, and restore and save config Shutdown all ports, reconnect the correct cables, and enable all ports
- Replace the failed unit, connect the correct cables, boot up the new node in recovery mode, upgrade firmware and restore, and save config Then, reboot and wait for VSX to synchronize.
- Replace the failed unit, connect the correct cables, boot up the new node and wait for VSX to synchronize configuration and firmware.
Correct answer: A
Question 2
(Scenarios may contain multiple errors which may or may not Impact the solution) Refer to the exhibit.
An engineer has attempted to configure two pairs of switches in the referenced configuration, it is required to implement Multi-Chassis Link Aggregation for each pair of switches The ports of the Aruba 8325 switches used for Agg01 and Agg02 are populated as follows:
There is an error message staling "incompatible interface." Which interfaces are the cause of the error? (Select two.)
- 1/1/12 10GBaseT SFP*+ 30m Cat6A Transceiver
- 1/1/49 40G QSFP+ 15m Active Optical Cable
- 1/1/13 10GBaseT SFP+ 30m Cat6A Transceiver
- 1/1/48 iGBaseT 100m Cat5e Transceiver
- 1/1/50 40G QSFP+ 15m Active Optical Cable
Correct answer: BE
Question 3
A customer wants to verify the proposed configuration snippets to create a point-to-point link between Aruba Switch and a third-party switch.
Will this configuration work with static routing?
- No, the configuration will not work, because the Aruba Switch has an MTU mismatch which will prevent IP communication.
- No. the configuration will not work, because the Aruba Switch does not have a locally reachable IP address from the third-party switch.
- No. the configuration will not work because the Aruba Switch does not have the "routing" command on it
- yes, the configuration should work fine and has no issues
Correct answer: C
Question 4
You are working with a customer whos has a paw of Aruba 8325 switches configured for Multi- Chassis Link Aggregation The customer is complaining that users are experiencing intermittent packet drops. Which action should be taken to quickly aid you in identifying the cause?
- Enable debug of vri with "console" set as the destination
- Setup a mirror session to generate a Tshark file.
- Setup a mirror session to niter packets for TCPDUMP analysis
- Check the configured VLANs using "show vsx config-consistency"
Correct answer: D
Question 5
How Is voice Traffic prioritized correctly on ArubaOS-CX switches?
- By placing it in the strict priority queue
- By defining voice VLANs inside VLAN context
- By attaching the QoS settings directly to device profiles
- By implementing TOS-profiles
Correct answer: D
Question 6
The customer is currently planning the migration of their current switches from the existing Aruba 5400R to ArubaOS-CX 6400. Which statements are correct about the mitigation of rogue DHCP servers with the selected product?
(Select two )
- With Aruba CX 6400 configure dhcp-snooping for the selected VLANs with authorized servers
- DHCP snooping can be enabled on ArubaOS-CX switches, once it's disabled on ArubaOS switches for same VLANs
- DHCP snooping is supported on both IPv4 and IPv6
- DHCP snooping needs to be enabled per VRF basis on Aruba CX 6400
Correct answer: AB
Question 7
Refer to the exhibit.
For all traffic within VLAN 10. a remark action or DSCP value EF must be set
For all traffic exiting VLAN 10, a remark action of DSCP value AF41 must be set Which is the correct configuration?
Correct answer: A
Question 8
The customer is considering Implemented the following VSX configuration that will host an Aruba mobility cluster servicing 9000 dual stack employee devices.
The client's default gateways will be hosted on the VSX stack. The customer is seeking advice about how to ensure ArubaOS-CX VSX best practices have been applied.
What advice can you offer the customer? (Select two)
- The ISL Bandwidth should be upgraded
- Agg-1 and Agg-2's hardware forwarding table profile should be changed to "L3-agg''.
- The -system-mac' of Agg-1 should be changed to an unused address from the unicast private address range
- The vsx linkup-delay timer is unnecessarily high; it should be reduced to prevent excessive delay of packet forwarding when a VSX peer joins an existing master.
- The Keepalive interface should be changed to interface LAG2 so there is redundancy through the mobility cluster.
- The keepalive subnet is misconfigured, it has an inappropriate address on Agg-1.
Correct answer: BF
Question 9
(Scenarios may contain multiple errors which may or may not Impact the solution > Refer to the exhibit.
An engineer has attempted to configure two pairs of switches in the referenced configuration it is required to implement VSX keep-alive at the aggregation layer.
The ports of the ArubaOS-CS 8325 switches used for Agg01 and Agg02 are populated as follows:
The configuration of switch AGG01 includes:
VSX keep-alive is not working. Which modification should you make lo resolve the error condition?
- Edit interface 1/1/48, adding the command "vpn-instance KA"
- Modify the Interface lag 2 command, removing "multi-chassis"
- Modify the Keepalive peer 192.168.20.2 source 192 168.20.1 command, adding "vrf KA"
- Edit the vsx-sync command, adding "keep-alive"
Correct answer: B
Question 10
(Scenarios may contain multiple errors which may or may not impact the solution ) Refer to the exhibit.
An engineer has attempted to configure two pairs of switches in the referenced configuration It is required to implement VSX at the aggregation layer The pons of the ArubaOS-CX 8325 switches used for Agg01 and Agg02 are populated as follows:
The configuration of switch AGG01 includes
The VSX cluster is not forming. Which modification should you make to resolve the error condition?
- Modify the system interface-group 4 speed tOg command change "25g" to "10g"
- Modify the keepalive peer 192.168 20.2 source 192 168.20 1 command, changing "vrf KA" to "vrf mgmt"
- Edit the vsx-sync command, adding "keep-alive"
- Modify the vsx definition, changing "inter-switch-link lag 2" to" inter-switch-link lag 256"
Correct answer: A
HOW TO OPEN VCE FILES
Use VCE Exam Simulator to open VCE files
HOW TO OPEN VCEX AND EXAM FILES
Use ProfExam Simulator to open VCEX and EXAM files
ProfExam at a 20% markdown
You have the opportunity to purchase ProfExam at a 20% reduced price
Get Now!